Cutback bitumen RC-30

Cutback bitumen RC-30 Description

Cutback bitumen RC-30 is an asphalt cement that has a solvent or distillate such as gasoline, diesel fuel, kerosene, or naphtha added to make the asphalt liquid at ambient temperatures and improve its ability to coat aggregates. Two letters followed by a numerical digit designate or name a cutback asphalt.
Cutback asphalt can contain between 12 and 40 percent distillate. The high demand for the distillates to be used in energy applications and ever-increasing air quality regulations have caused a steady decline in the use of cutback asphalt.
When gasoline or naphtha is used to flux asphalt cement, the final product is called “rapid curing” (RC) cutback asphalt. Specifications permit up to 45 percent distillate in manufacturing an RC-30 cutback asphalt.

Our Cutback Bitumen RC-30 complies with cutback petroleum asphalts of the rapid-curing type for use in the construction and treatment of pavements as per ASTM D2028-97 reapproved in 2004. Cutback Grade Bitumen is normally used in spraying and in some mixing applications. Cutback Bitumen is penetration grade bitumen blended with a solvent such as kerosene, white spirit, gasoline, and naphtha, controlling the curing time. Cut back petroleum asphalts of the rapid curing type supplied by Huei Jie Co. are petroleum grade bitumen manufactured from the fractional / vacuum distillation of crude oil blended with a solvent. Bitumen supplied by Huei Jie Company is produced from the vacuum residue (short residue) feedstock. Penetration Grade bitumens are specified by the penetration and softening point test. Designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability, and application temperatures of bitumen. The cutback bitumen (Asphalts) supplied by Huei Jie are blended from petroleum grade bitumen as stated herein.

Cutback Bitumen RC-30 Applications

Current common uses are in penetrating prime coats and in producing patching or stockpile mixtures. Cutback asphalt used in mixing with aggregate will usually contain an adhesion agent to assist in the coating of the aggregate surface.

RC-30 Packing

This cutback bitumen bulk in the tanker and also in new steel and thick drum on the pallet to prevent all leak inside of the container.

RC-30 Safety

Refer to Safety Data sheets before use.
Transport, use and store at the lowest temperature possible.
Eliminate all potential ignition sources during application.
Avoid breathing vapors. Avoid contact with skin.
Always wear appropriate PPE including heat protection when used hot.
DO NOT allow product or washings to enter stormwater or sewer systems.

RC-30 Characteristics

Huei Jie Company guarantees that the Rapid curing CutBack Grade RC-30 it supplies under its offers is produced in compliance to and is in conformity to ASTM D-2028-97 Rev 2004 and is compliant to the following specification requirements.

property specification limit  Test method
Min Max
Kinematic viscosity at 60°c ,cST 30 60 ASTM D2170
Flashpoint(tag open cup), °c ASTM D3143
Distillation test
Distillate, volume percent of total Distillate to 680°f(360°c)
to 437°f(225°c)
To 500°f(260°c)
to 600°f(316°c)
Residue from distillation to
680°f(360°c), percent volume by difference
55
75
90
50
ASTM D402
Test on Residue from distillation test
Penetration 77°f(25°c) 100g,5s mm 80 120 ASTM D5
Ductility 77°f(25°c) 5cm/min cm 100  — ASTM D113
Solubility in trichloroethylene % 99  — ASTM D2042
Water, percent volume  — 0.2 ASTM D95