Cationic Bitumen Emulsion CSS-1

Cationic Bitumen Emulsion CSS-1 Description

Bitumen emulsion consists of three basic ingredients: bitumen, water, and an emulsifying agent. Based on specifications it may contain other additives, such as stabilizers, coating improvers, anti-strips, or break control agents. It is well known that water and asphalt will not mix, except under carefully controlled conditions using highly specialized equipment and chemical additives.
Cationic Bitumen Emulsion CSS-1 is a cationic emulsion. Bitumen emulsion CSS-1 are usually made by passing the mixture of hot bitumen and water phase between a rotating disc, cone or wheel and a stator. In the emulsification process, the hot binder is mechanically separated into minute globules and dispersed in water treated with a small quantity of emulsifying agent. The water is called the continuous phase and the globules of the binder are called the discontinuous phase by proper selection of an emulsifying agent and other manufacturing controls.

Cationic bitumen emulsions CSS-1 have a positive charge and hence a direct and very rapid reaction between the emulsion and an aggregate or pavement is possible. The size of the charge or the Zeta potential affects stability, the larger the charge the greater the repulsion, but as the aggregate is negatively charged the higher the zeta potential the more rapid the reaction.
So it is possible to stabilize a cationic emulsion in the same way that makes it a more rapid break. The other mechanism of evaporation is available too but as the emulsion is stabilized this form of break becomes slower. Thus a balance must be struck.After the electrostatic part of the reaction is complete the emulsion will rely on flocculation and coalescence to complete break.
After the break is completed the water must still be completely evaporated for the residual Asphalt to achieve full strength.

531103_558566177503548_641932834_n-768x576

Bitumen Emulsion CSS-1 Applications

Cationic emulsions may be used at ambient temperatures with aggregates, which need not be completely dry. Emulsions are less hazardous to use in comparing with the cutback and can be applied in a wider range of conditions. Most CSS-1 applications are listed below:

  • Biturubber (Rubber)
  • Bitumalch (Malching)
  • Prepared cold Mixed Asphalt
  • Bituprime (Prime Coat)
  • Bitucoat (Fog Seal – Seal Coat)

Successful performance of bitumen emulsions requires selecting the proper type and grade for the intended use. Guidelines presented in this chapter should help select the specific grade and type of emulsion to be used.
The first consideration in picking the right type and grade of the emulsion is how the emulsion will be used. Is it for a planned mix (central or mixed-in-place), a recycled mix, or a prime coat application? Is it for some type of surface application, such as a fog seal, slurry seal, micro surfacing, or chip seal? Is it for a maintenance mix? Once this decision is made, other project variables must then be considered. Some other factors that affect the selection are:

• Climatic conditions anticipated during construction. The choice of emulsion grade, the design of mix or treatment, and the selection of construction equipment should be dictated by the conditions at the time of construction.
• Aggregate type, gradation, and availability.
• Contractor or construction equipment availability.
• Geographical location. The hauling distance and, in some cases, water availability are important considerations.

the hauling distance and, in some cases, water availability are important considerations.
• Traffic control. Can traffic be detoured or only controlled through the work area?
• Environmental considerations.
• Proper application for pavement preservation or pavement distresses.
• Traffic type and volume.

While general guidelines can be given for selecting emulsions, laboratory testing is strongly recommended. There is no substitute for a laboratory evaluation of the emulsion and the aggregate to be used. Different types and quantities of emulsion should be tried with the aggregate to find the best combination for the intended use. An experienced technician can determine the type and grade of the emulsion to be used.
Cationic emulsions are preferred for use with negatively charged siliceous aggregates such as quartz, granite, sandstone and river gravel. In general, Cationic emulsions can be used with a wider range of aggregates, will tolerate greater quantities of moisture, and will break at a lower ambient temperature. The main application areas of Emulsion bitumen are surface dressing, tack coats, prime coat, slurry seal, and cold mixing.

Dust control (SS-1, CS-1, CRS-1)
Tack coat (SS-1, SS-1h, CSS-1, CSS-1h, CRS-1)
Prime coat (SS-1, SS-1h, CSS-1, CSS-1h)
Fog seal (SS-1, CSS-1, MS-1-CMS-2, CRS-1)
Penetration prime (SS-1)
Cold mix asphalt, Mulching, Asphalt Sealers (CSS-1)
Chip seal, single, or multiple treatments (RS-1, RS-2, HFMS-1, HFMS-2, HFRS-2, CRS-2, and CRS-2P)
Sand seal (SS-1, SS-1h, CSS-1, CSS-1h, CMS-2s, CRS-1, CRS-2)
Slurry seal (SS-1h, CSS-1h, CSS-1Hp)
Sandwich seal, cape seal, chip seal (CR-2)
Micro surfacing (CQS-1h)
Structural and surface plant mixture (SS-1, SS-1h, HFMS-2s, CSS-1, CSS-1h,)
Stockpiled patching mixture (HFMS-2s, CMS-2s)
In-place road mixing (SS-1, SS-1h, HFMS-2s, HFMS-2, HFMS-2h CMS-2, CMS-2h, CSS-1, CSS-1h)
Crack filler, joint coating (RS-2, HFMS-2h, MS-2, CMS-2h, CRS-2P)
Asphalt sealers, Immediate Maintenance, Stockpile Maintenance Mixes (CMS-2)
Immediate Maintenance (CM2, CM2h)

CSS-1 Advantages

• No petroleum solvent required to liquefy
• Little or no hydrocarbon emissions
•Because of low viscosity of the Emulsion as compared to hot applied Bitumen, The Emulsion has a good penetration and spreading capacity.
• In most cases, used with no additional heat. It does not need any pre-heating. Thus results in the case of handling for the user, besides saving in cost.
• The ability to coat damp aggregate
• Can use cold materials at remote sites. Cold application of Bitumen Emulsion ensures safety to the workforce; it is a user-friendly product. Being cold applied the work progresses much faster.
• Wide variety of emulsion types available today
• Economical
• Free from danger ( for fire )
• Environmental
• Harmless for worker health.
• It can use with moisture aggregates. It can be used even with wet aggregates thus enabling users to carry out work during the monsoon also.
• Application temperature is low and does not need heating while storage and transportation period. For this reason, it provides energy saving.
• Emulgators increase adhesion they effect as anti-stripping agent
• It can use in four seasons. Especially it gives a chance application in the rainy region and it extends application period.
• It has a lot of application area and construction methods.
• Bitumen Emulsion does not require petroleum solvent to make them liquid as in cut back and also it is not required to be heated like normal Bitumen. Thus saving imported petroleum oil or firewood.
• Toxic fumes (Hydrocarbon emission) normally emitted from heated bitumen & cutbacks not present when Cationic Bitumen Emulsion is used, as no heating is required for its application.
• Energy saving & control of pollution & safety:
During the last 10-12 yrs., the country was in the quest for alternatives to Hot Mixing technology especially to save our beleaguered environment besides curbing the use of Imported petroleum oil, and our precious forests supplying firewood. Optimum use of Bitumen-emulsions can preserve Petroleum Oil and in turn, save our Environment and Foreign Exchange.s application.

CSS-1 Packing

Packing of bitumen emulsion CSS-1 is in a new thick steel drum on a pallet to prevent any leak inside of container also bulk in bitutainer and tanker.

Cationic bitumen emulsion CSS-1 Characteristics

Emulsion Type: Slow-Setting
Grade: CSS-1
Standard: ASTM D 2397M – 13

PropertyProperty  Min Max Test Method
Test on Emulsions
Viscosity, Saybolt Furol at 25 °C, SFS 20 100 ASTM D244
Storage stability test, 24-h, % 1 ASTM D6930
Particle charge test positive ASTM D244
Sieve test, % 0.1 ASTM D6933
Cement mixing test, % 2.0 ASTM D6935
Distillation:
Residue, % 57 ASTM D244
Tests on residue from distillation test:
Penetration, 25°C (77°F), 100 g, 5 s 100 250 ASTM D5
Ductility, 25°C (77°F), 5 cm/min, cm 40 ASTM D113
Solubility in trichloroethylene, % 97.5 ASTM D2042